Skip to content Skip to sidebar Skip to footer

Widget HTML #1

600W Audio Amplifier Circuit with 2SC5200 2SA1943 and PCB

600W Audio Amplifier Circuit with +85V 8Ohms
This amplifier power spec is 600W with the stereo system. with this power amplifier 600w, you can use it for amplifying your audio for home or public amplifier. This circuit is matched for power amplifier home and public audio. But also you can use for car audio. 

I'd say a fanatic audio amplifier circuit with completely sound and popular using transistor 2SC5200 2SA1943 This circuit takes high-quality electronic components with pair power amp good function and PCB has not bug.


Managing heat of transistor power with the light heatsink that guarantees is not overheat.

600W Audio Amplifier Circuit with  2SC5200 2SA1943
By using a heatsink on final transistor amplifier it useful, because the power amplifier on the final transistor is very hot on high performance, so the heatsink is to reduce hot on the final transistor. You can use an aluminium plate for the heatsink. 



 Technical information
1.Input section responsibility =1.43 RMS
2.Power of amplifier = 600+600W at 85Volt
3.Input Impedance 85000 ohms.
4.THD less than 0.008% at 20 Watts 1000Hz
5.Frequency responsibility 0.3dB at 20Hz and 20KHz
6.Hum and noise less then 177dB 120Hz-20KHz

 Sure!, We have provided schematic, PCB and electronic part list for your build it.
600W Audio Amplifier Circuit with  2SC5200 2SA1943

On schematic above is describe the 600 Watt power amplifier circuit and the voltage input source is about 85VDC. 

Below the PCB Layout design for it amplifier.
 Click On Image And Zoom
600W Audio Amplifier Circuit with  2SC5200 2SA1943
And Picture below is electronic part list of this circuit
600W Audio Amplifier Circuit with  2SC5200 2SA1943

22 comments for "600W Audio Amplifier Circuit with 2SC5200 2SA1943 and PCB"

  1. Please send the Proteus file to [email protected] Also what's the ampere rating of the transformer

    ReplyDelete
    Replies
    1. i dont have the proteus file . ampere rating use upto 10Ampere

      Delete
  2. This circuit have any error?

    ReplyDelete
  3. Dc offset setting is difficult. voltage is not going to 0v.any solutions? Amplifier is working.out put humming

    ReplyDelete
  4. I did every wiring and PCB very correctly.but output can't set 0v.always showing 235 Milli voltage.and main heat sink also heat.preset can't adjust.i things this circuit have major error

    ReplyDelete
  5. Kindly let me know what is the transistor no which you have used for the relay switch which you have used on your 300 watt amplifier circuit. Reply
    [email protected]
    Tks

    ReplyDelete
  6. Kindly let me know what is the transistor no which you have used for the relay switch which you have used on your 300 watt amplifier circuit. Reply
    [email protected]
    Tks

    ReplyDelete
  7. Yes but 300 Watt amplifier made out of 2N3773 out put transistors.
    Also I don't see the part list for the 700 Watt amplifier circuit

    ReplyDelete
    Replies
    1. you can search here abot speaker protector circuit

      Delete
  8. Still I am unable to complete this project as your advise is insufficient. The speaker protection is given on your pcb but the transistor numbers are not mentioned and two E.Condender positive negative side is not marked. kindly help me.
    Raj

    ReplyDelete
  9. Send me your e mail id sothat I could maild the pcb.
    Raj

    ReplyDelete
  10. What voltage should i use..?
    What is the ampear..?

    ReplyDelete
  11. You can use voltage about 70V with 10A amp rating

    ReplyDelete
  12. Hello Dr please send me PBC layout lifier-zip
    600W Audio Amplifier Circuit with 2SC5200 2SA1943 and PCB

    ReplyDelete