Skip to content Skip to sidebar Skip to footer

Super Power Amplifier Yiroshi Audio - 1000 Watt

Super Power Amplifier Yiroshi Audio 1000W
This Yiroshi audio power amplifier has a low character and has high power output, so many audio lovers choose this type of amplifier because the bass boom is very pronounced. To make this Yiroshi audio amplifier so powerful need a power supply which is sufficient to let the results that can at maximum transformer minimum 20A 45-75v output and the good quality of components.

Below the circuit diagram of Yiroshi audio power amplifier driver + final transistors:
Yiroshi amplifier 1000W 1kW output power circuit diagram
Component List
Resistor
R1=2k2, R2=47k, R3=100R, R4=100R, R5=56R, R6=56R, R7=56R, R8=56R, R9=47k, R10=100R, R11=2k2, R12=2k2, R13=100R, R14=47K, R15=2k2, R16=2k2, R17=100R, R18=100R, R19=100R, R20=100R, R21=220R/1W, R22=220R/1W, R23=100R, R24=1k8, R25=1k, R26=10k, R27=56R, R28=56R, R29=100R/1W, R30=100R/1W, R31=120R/1W, R32=120R/1W, R33=100R, R34=100R, R35,R36=220R/1W, R337,R38=220R/1W, R39,R40,R41,R42,R43,R44,R45,R53,R54,R56,R57,R58,R59=0R22/5W, R46,R47,R48,R49,R50,R1,R52,R60,R61,R62,R63,R64,R65,R66=10R/0.5W, R67=10R/5W + L1 10uH, R68=10R/1W

Capacitor
C1=1u Nonpolar, C2=330pF, C3=4n7, C4=4n7, C5=100uF/100V, C6=100uF/100V, C7=330uF/50V, C8=12pF, C9=12pF, C10=100N, C11=47pF, C12=150pF, C13=150pF, C14=100N

Transistor
Q1,Q4,Q7,Q8=2N5401
Q2,Q3,Q5,Q6=2N5551
Q9,Q13=2SC4793
Q10,Q12=2SA1837
Q11=MJE340
Q14=TIP2955/2SA1962
Q15=TIP3055/2SC5242
Q16,Q17,Q18,Q19,Q20,Q21,Q22=2SA1943 or you can change other PNP final power transistor
Q23,Q24,Q25,Q26,Q27,Q28,Q29=2SC5200 or you can change other NPN final power transistor

Final Power Transistor Audio Amplifier List
2SC5200/2SA1943 : 230volt 15 ampere 150 watt
2N3055/MJ2955 : 100 volt 15 ampere 150watt
TIP3055/TIP2955 : 100 volt 15 ampere 150watt
2N3773/2N6609 : 160volt 16 ampere 160watt
MJ15003/04 : 140volt 20 ampere 240watt
MJ15024/25 : 400volt 16 ampere 240watt

Sanken 2SA1295-2SC3264 : 200volt 17 ampere 200watt
Sanken 2sa1494-2sc3858 : 200volt 17 ampere 200watt
Sanken 2sa1216-2sc2922 : 180volt 17 ampere 200watt

Toshiba 2SA1095/2SC2565 : 160volt 15 ampere 150watt
2SC5200/2SA1943 : 230volt 15 ampere 150 watt
2N3055/MJ2955 : 100 volt 15 ampere 150watt
TIP3055/TIP2955 : 100 volt 15 ampere 150watt
2N3773/2N6609 : 160volt 16 ampere 160watt
MJ15003/04 : 140volt 20 ampere 240watt
MJ15024/25 : 400volt 16 ampere 240watt

Sanken 2SA1295-2SC3264 : 200volt 17 ampere 200watt
Sanken 2sa1494-2sc3858 : 200volt 17 ampere 200watt
Sanken 2sa1216-2sc2922 : 180volt 17 ampere 200watt
Toshiba 2SA1095 / 2SC2565 : 160volt 15 ampere 150watt
2SA1103 / 2SC2578 : 100volt 7 ampere 70 watt
2SA1105 / 2SC2577 : 120volt 9 ampere 90watt
2SA1106 / 2SC2851 : 140volt 10 ampere 100watt
2SC2580 / 2SA1105 : 120volt 9 ampere 90watt

2SC2581 / 2SA1106 : 140volt  10 ampere 100watt

Buy these parts, go to Allchips.

PCB Layout Driver Power Amplifier Yiroshi Audio

PCB Layout Power Amplifier Yiroshi 1000W output

PCB Parallel Final Power Transistor 7 Set Toshiba 2SC5200 2SA1943
PCB Layout Power Amplifier Final transistor booster

Final Power Transistor Assembling 2SC5200 and 2SA1943
Final Power Transistor 2SC5200 2SA1943 power amplifier

Wiring Diagram Driver Power Amplifier and Final Power Transistor
Wiring Diagram Driver Power Amplifier and Final Power Transistor

For this Yiroshi power amplifier project, I make a separate PCB driver with the final transistor, you can see on both picture PCB Layout above. The power amplifier is very good and high performance. You can upgrade again to add power amplifier by adding the final transistor and also replace it with more power, current, and stronger voltage. And also must be balanced with a larger power supply current and voltage. For more details see the full interesting video below:




96 comments for "Super Power Amplifier Yiroshi Audio - 1000 Watt"

  1. This circuit have some problems after 4 to 5 min power transistor dead

    ReplyDelete
    Replies
    1. no, please see at circuit diagram. There is no erorr, you must adjust bias voltage.

      Delete
    2. it can work normally not just a minute.

      Delete
  2. Good amplifier and thanks for your video

    ReplyDelete
  3. Thanks for video and project.

    ReplyDelete
  4. we are happy to comment here, and we await your komantar in our blog

    ReplyDelete
  5. Hello,
    The amp as shown in schematics will NOT work. Q15 should be NPN type, prrobably TIP3055, although I think this is a bad choice as TIP3055/TIP2955 have Vce max of only 70V.
    Cheers

    ReplyDelete
    Replies
    1. Q14=TIP2955/2SA1962
      Q15=TIP3055/2SC5242
      you can choose these transistor

      Delete
    2. the power amplifier is work, you can see the video testing amplifier

      Delete
  6. I saw some other videos the same circuit but there is no trimpot or bias circuit

    ReplyDelete
  7. But on the assembling video i saw there is bias tripot I'm confused, but anyway thanks a lot for sharing this powerful amp i will try to build very soon. Thanks a lot god bless..

    ReplyDelete
    Replies
    1. try to use it cause the trimpot can adjust bias voltage if you using any finalt transistor type.

      Delete
  8. what are the sizes of the PCB?

    ReplyDelete
  9. hai i want pcb and components all so price please my email id: [email protected]

    ReplyDelete
  10. how to adjust the trimpot in the amplifier driver

    ReplyDelete
  11. Hi sir romadhon, I'm back after building this power amp it sounds nice even though i tested it on 65v 8.5A so not enough power supply. Im Wondering on the pnp final output power they are warmer than the npn output i have noticed the predriver 2SA1837 for pnp output is warmer also is this normal? Because still sounds good or maybe i will get problems in the future. Please help

    ReplyDelete
    Replies
    1. You can change the emitter resistor by using 220R 1w. and also the npn transistor

      Delete
  12. hi how are you can you tell me how to download the PDF, thanks

    ReplyDelete
  13. Sir can i use 90v symmetrical ?

    ReplyDelete
    Replies
    1. yes im using 110V its normally. but you must have larger heatsink

      Delete
  14. Sir what voltage should I use for 12pairs 5200/2943 transistor output?

    ReplyDelete
  15. Can I use IRFP240 and IRFP9240 for this project?

    ReplyDelete
    Replies
    1. It can't if you use final mosfet. see class d d4k5 its bigger power than this amp. if you want mosfet class d amp

      Delete
  16. sir i am using with mjl21194,mjl21193 14 pair ? which use driver ..and volt ? ampere ?..

    ReplyDelete
    Replies
    1. you can use this driver or yamaha PA-2400, 80 upto 100V is recomended try using 20A current transformer ar SMPS circuit.

      Delete
  17. Nice amp sir but sir you use cliping indictor and protection ckt

    ReplyDelete
  18. If i use 8 transistor instead of 14 transistor in the final driver Will the amplifier still work?

    ReplyDelete
  19. what current rating should the L1 coil be

    ReplyDelete
  20. Is it possible to send me better quality PCB, and PCB size, and layout files, also schematic diagram please [email protected]

    ReplyDelete
  21. Where do I put the trimpot to regulate the OFFSET voltage?

    ReplyDelete
  22. can you tell me the base voltages of 1943 and 5200 mine is .1 and .4 mv

    ReplyDelete
  23. can you tell me the base voltages of 1943 and 5200 mine is .1 and .4 mv

    ReplyDelete
  24. Puedes pasar el pdf y las medidas exactas de la placa en que parte del diagrama va el trimpot

    ReplyDelete
  25. Hi sir,how to order the PCB and components parts of 1kwatt amp.

    ReplyDelete
  26. where can I order PCB please, is there a link

    ReplyDelete
  27. i can't see the sizes of PCB sir ?
    can u please help me sir.

    ReplyDelete
    Replies
    1. you just download PDF and print it!
      its actual size print.

      Delete
  28. hey..I want to buy all the components of this amplifier.. how can I contact u.. my email is [email protected]

    ReplyDelete
  29. Sir if i want to put trimpot which should i put there ?ty

    ReplyDelete
  30. Sir can i use in the circuit 10 pairs of final transistors then the speaker out is? Watts and Witch transformer I can use please tell me sir

    ReplyDelete
  31. Can i use 55ac o 55acv 20 ampere it is ok sir

    ReplyDelete
  32. Its nice sound.what is the best vac in power amp i have 7 set of 2sc5200 and 7set of 2sa1943 what is the best amphers and Vac 45 something?

    ReplyDelete
  33. Hey ' i need purchase this amplifier subwoofer kit ...how purchase ??

    ReplyDelete
    Replies
    1. https://www.ebay.com.au/itm/123348339586

      Delete
    2. Yes after I corrected the errors on PCB layout, and found a schematic that was correct, have sold over 350 so far, I also have the Crown XLS 6 fet as well, with corrected schematic and PCB, only sold 275 of the so far

      Delete
  34. there is a huge demand for these amplifiers, but a lot of errors, or cannot read schematic, and exaggerating the output wattage...people want the truth, when they purchase, that's what I am doing

    ReplyDelete
  35. hola amigo tengo un problema en las resistencias de 220 y 100 ohs se me esta calentando y se terminan quemando como corrijo ese problema

    ReplyDelete
  36. schematic diagram doesn't have diodes and ohms for R24 and R25 should be flip. can you update the schematic diagram with trimpot

    ReplyDelete
  37. This is where you get PCB, with all the errors fixed, as the layout from wahyu eko romadhom will only work for approx 3 mins then it destroys itself, here is link to PCB that WORKS https://www.ebay.com.au/itm/123561661498?var=&ssPageName=STRK:MESELX:IT&_trksid=p3984.m1555.l2649

    ReplyDelete
  38. Hola disen que ay que cambiar 2 resistensias las lateralrs de 4k7 por 47k

    ReplyDelete
  39. how many watts on base on resistors? .25 watts or .5 watts

    R1=2k2, R2=47k, R3=100R, R4=100R, R5=56R, R6=56R, R7=56R, R8=56R, R9=47k, R10=100R, R11=2k2, R12=2k2, R13=100R, R14=47K, R15=2k2, R16=2k2, R17=100R, R18=100R, R19=100R, R20=100R,

    ReplyDelete
  40. Hi sir i just need to ask where to adjust dc offset of this amp i need to adjust to 0V dc there's only one trimpot but adjust only for the current bias.

    ReplyDelete
  41. Hi sir i just need to ask where to adjust dc offset of this amp i need to adjust to 0V dc there's only one trimpot but adjust only for the current bias.

    ReplyDelete
  42. How to make the 10 uh coil bro
    Explain the guage of wire and how many turns wanted

    ReplyDelete
  43. Sir it working but humming problems and transistors hitting very quickly
    Please solve the problem sir

    ReplyDelete
  44. In the drawing of squematic,the Q15 transistor isn't wrong?

    ReplyDelete
  45. Dor,
    Can you please Tell us where tô find a correct esquematic whith ALL the erros fixed.
    After few minuts It burns!
    In the squematic there os no trim por, Q15 os misdrawed, André i real life ,some resistores must vê chances.
    Thank You Very much!!!!!

    ReplyDelete
  46. do you have available pcb layout for project,.,can i buy?

    ReplyDelete
  47. Sir....Can you reply... What is the PCB size...???

    ReplyDelete
  48. In the squematic there os no trim por, Q15 os misdrawed, André i real life ,some resistores must vê chances. no, please see at circuit diagram. There is no erorr, you must adjust bias voltage.

    ReplyDelete
  49. can you send me Gerber files sir.

    ReplyDelete
  50. can i use TTC5200 in exchnge 2sc5200

    ReplyDelete
  51. por los comentarios y lo visto otro MAS QUE NO SIRVE CERO Y VAN DOS si es que funciona deberias contestar dudas no creo que te cueste mucho trabajo y tener mas atencion con tus seguidores

    ReplyDelete
  52. Sir. I make 1000w mono amplifire using this driverboard. I want to use subwoofers on it. What can i do for it?

    ReplyDelete
  53. Have a reference blog / idol blog. Important for a blogger to have a reference Take for example, I like a blogger on this site.

    ReplyDelete
  54. Have a reference blog / idol blog. Important for a blogger to have a reference Take for example, I like a blogger on this site.

    ReplyDelete
  55. do you have preamp of yiroshi amplifier ?

    ReplyDelete
  56. This comment has been removed by the author.

    ReplyDelete
  57. What exactly is the quiet current in the yiroshi amplifier?

    ReplyDelete
  58. this amp has a trap door, replace the components with the xls602

    este amplificador tiene una trampita, reemplace los componentes por los de la xls602

    ReplyDelete
  59. After reading all the comments was the above schematic corrected

    ReplyDelete