Skip to content Skip to sidebar Skip to footer

700W Power Amplifier with 2SC5200, 2SA1943

700W Amplifier Adjust the amplifier power 700W looks calm, but we requirement not put out of your mind to the adjustment happening forcing transistors, the whole relating to-engagement of frequency offset. It is compulsory to change the current insurance rule which serves to guard the final transistors.

Their tendency to happen allowable to keep the transistors in the SOAR characteristics. primary it was needed to evaluate all the necessary resistors and subsequently measured to verify the accuracy of the calculations, it is managed with satisfactory results.


Peripheral changes required in support of it to be there able to consistently amplifier to supply power. - First you need to restore the 2k2 resistors stylish string with the LEDs on Zenerovými resistors with upper wattage. be enough 1/2W resistors, power loss next to 80V +-based 1W. - therefore was traded 1k2 resistor in the pointer resistor by the side of 620 ohms. 

700W Power Amplifier with 2SC5200, 2SA1943
700W Power Amplifier with 2SC5200, 2SA1943 Circuit Diagram
Which is the initial reap has doubled, so at this point is the overall gain amplifier 40 and the limit excitation is sufficient to 1V rms. - Předbudiči transistors were replaced by stronger MJE15032/33 since KF467/470 are permitted satellite dish current 20mA - by the side of the exciter output stages are used the same transistors for example the output stage. - add up to of terminals of transistors has been increased to eight pairs - It had to occur to compensate designed for the excitation level by calculation a capacitor 10pF to 47pF + 22K appendage.

This led to a slight "gradual" amplifiers, but this did not affect the ensuing parameters. This power is tuned correctly in support of this type of terminal transistors 2SA1943/2SC5200. 

With with the purpose of it is a least assessment next to which the amplifier operates stably exclusive of pass by the side of the rising and falling edges of the genuine. - The ultimate adjustment, the adjustment terminal current protection transistor.




The final transistor characteristics shows with the intention of the most allowable radio dish current once the voltage of 1.5 A is ideal in favor of cooling, so it's essentially not as much of. Therefore, the current protection is customary to 12A, single-arm.

This impersonate protection SOAR transistor characteristics. curt-circuit current is regarding 6 A which is about 075A for every transistor. This is far beneath the SOAR characteristics. The mechanical design is relatively clear-cut, the transistors are placed on the two cooling profiles with a height of 66 mm, width 44mm, overall part 260mm.

They are twisted contrary to each one other in this way, from the cooling tunnel. Coolers are attaching the nylon aid which allows the compilation of transistors exclusive of washers, and thus better conveying tepla.DPS amplifier next to the top of the tunnel and the transistors are soldered from the underside of PCB.

700W pcb power amplifier

41 comments for "700W Power Amplifier with 2SC5200, 2SA1943"

  1. sir
    i made it .45v 10amp dc volt . power filter is 100 v 1000uf 4 pic capasitor . when i use Ac series bord Amplyfire playing good. But if i plug in direct ac fuse is cut after 5 scened.all ware is good . speaker is 15 inc jbl.can't understand what is the problem.hitstic is normal hot. everything is nice if i use electric bulb seris bord .

    ReplyDelete
    Replies
    1. Amazing ,, its normally power amplifier.

      What the value number of Fuse Ampere?

      Delete
  2. How much volt and amp transformer i can use ?
    Which capacitor i can use for power filter ?

    ReplyDelete
    Replies
    1. for this power amplifier i recomennded using 75VDC - 95VDC you can using capacitor for power filter 4x 10000uF 100V or higher capacitance.

      Delete
  3. How about what kind of diodes are used??

    ReplyDelete
  4. I think must Use soft stat circuit for power supply.

    ReplyDelete
    Replies
    1. its true, and recomended using soft start for power supply circuit. you can search here for soft start circuit.

      Delete
  5. 90DCV will work on this circuit? I have 33 - 0 - 33 then if rectified the DCV goes 90dc. Please reply if is okay

    ReplyDelete
  6. Me pueden facilitar el circuito gracias

    ReplyDelete
  7. Quien me regala el circuito no lo tengo😂😂😂

    ReplyDelete
  8. Please and give me the circuit in mirror to make it thanks

    ReplyDelete
    Replies
    1. hello Robinson,

      there,the circuit and pcb layout is attachment on the post

      Delete
  9. 95vdc ok what should be the amperage be

    ReplyDelete
  10. this amplifier circuit is mono....when make 2 circuit for stereo how many ampier want for it in transformer?...

    ReplyDelete
  11. Wahyu Eko Romadhon sir i am waiting for your answer

    ReplyDelete
  12. tell me how many AC dual supply volts for this.....and ampiear in transformer?

    ReplyDelete
    Replies
    1. Using Symmetrical power supply, voltage about 70Volts with Ampere Rating 10A minimum.

      Delete
  13. is there a part list for this.
    [email protected]
    i see some diodes not named.CONNECTED TO BC556 BASE AND BC546
    is it a zener.
    also are there leds which is connected to 5K6 in the circuit.what are they used for.

    ReplyDelete
  14. Enter your comment...which value of portshometer that can put between 6k2and 1k

    ReplyDelete
  15. use trimpot with value 5k, it is using for adjusting bias voltage.

    ReplyDelete
  16. use trimpot with value 5k, it is using for adjusting bias voltage.

    ReplyDelete
  17. Thanx for reply me let me put it

    ReplyDelete
  18. Thanx for reply me let me put it

    ReplyDelete
  19. hi.What the value number of transistor
    between KF469 AND KF470???

    ReplyDelete
  20. How many watts resistors used for the output transistor on your 700 watt amp

    ReplyDelete
  21. KF469 AND KF470??? are not available.....can mje 340 and mje 350 be used???
    if not what is the replacement

    ReplyDelete
  22. i am currently working on the circuit and really excited to build this and i may need your assistance so for that reason can you kindly share your whatsapp no or email-id at [email protected]. Really eager fora reply. THANK YOU IN ADVANCE.................

    ReplyDelete
  23. you can visit the contact us, or visit facebook fanpage elcircuit

    ReplyDelete
  24. Sir if i use symmetrical 90vdc how much power it will be ?

    ReplyDelete
  25. What is power of this amplifier if i used 90vdc ?

    ReplyDelete
  26. If I use 70-0-70 full wave transformer then what will be the ampier for each side?
    Tks

    ReplyDelete
  27. Pak untuk ukuran panjan dan lebar pcbnya brp yaa?????

    ReplyDelete