Skip to content Skip to sidebar Skip to footer

DIY Stereo Yiroshi Power Amplifier 1400W

DIY Stereo Yiroshi Power Amplifier 1400W


This my second project for Yiroshi Power Amplifier Circuit, the power amplifier circuit is indeed very super quality, many have tested the strength of this Yiroshi power amplifier. Power amplifier yiroshi is suitable for outdoor or indoor. Previously I have made this yiroshi amp circuit in the mono version. I have also tested it in the unboxed state of the box, using only 2SC2922 and 2SA1943 final transistors, this amplifier is capable of high enough power until my speakers are damaged and also my smps is damaged This power amplifier is tough enough, none of my final transistors parallels broken.

here is the circuit scheme of the stereo power amplifier yiroshi, the scheme below is still the same with the yiroshi circuit that superpower driver before, only later will replace the transistor previously used TIP3055 and TIP2955 I replace it with transistor 2SC5200 and 2SA1943. Because the previous transistor has only a maximum voltage of 60Volt with a maximum current of 15Ampere, so it is advisable to use a larger transistor maximum voltage and current. If for 2SC5200 and 2SA1943 transistors this is enough for me, maximum CE CE voltage up to 230V and maximum current up to 15 Ampere.
stereo power amplifier yiroshi NJW0302 NJW0281
In the above circuit scheme is a combined stereo of two series of yiroshi power amplifiers, so to list the components to make it easier for you to buy, please just look at the previous post here Yiroshi Power Amplifier Circuit.

To make it easier for this yiroshi amplifier circuit you can use this PCB Layout design:
PCB Layout design for stereo power amplifier yiroshi.

PCB Final Transistor Parallel for stereo amplifier yiroshi driver.
PCB Layout transistor final for yiroshi amplifier

DIY PCB AND ASSEMBLING COMPONENTS STEREO YIROSHI AMPLIFIER (VIDEO)

I have made this stereo yiroshi power amplifier circuit, but this is still in the test process stage. and it turns out for PCB Layout for the driver you have to reverse the position of all transistors, so the same face with the top component layout. Later you will be able to see the location and position of the transistor, after the power amplifier is finished and ready to be produced.

For the final transistor, on this yiroshi stereo amplifier project, I do not use transistor Toshiba 2sc5200 and 2sa1943 as well as sanken transistor 2sc2922 and 2sa1216.

I am using transistor NJW0302 and NJW0281, the transistor price of NJW0302 and NJW0281 is almost the same as Toshiba transistor 2sc5200 and 2sa1943.

Both transistors both have 150Watt power output, and IC 15Ampere but for VCEO and VCBO are different, a 20Volt difference is higher transistor NJW0302 and NJW0281, where the maximum voltage is 250Volt.

The following is a final transistor picture of NJW0302 which is embedded in the PCB:
transistor NJW0302 and NJW0281 VS 2SA1943 2SC5200

And this is the final transistor image I've paralleled using the PCB Design layout above.I am using 14 pairs of NJW0302 and NJW0281 transistors and for per channel yiroshi driver I use 7 pairs of transistors.
Parallel final transistor NJW0302 NJW0281
Already tested power amplifier yiroshi I will supply with 20Ampere 60Volt Switching Mode Power Supply 
Stereo Yiroshi power amplifier high power amp circuit




High Power Amplifier Class D fullbridge Deep Bass Ever test

Download File PCB Layout.PDF
PCB Stereo Yiroshi Amplifier
Transistor Final Top
Transistor Final Bottom

63 comments for "DIY Stereo Yiroshi Power Amplifier 1400W"

  1. Very nice love 😍 it! is this better than the previous Yiroshi without bias trimpot. Thanks a lot

    ReplyDelete
  2. Hello Mr. Manager.I would like to learn about your drawings, it is 800w 1000w, 1500, 1600w, 1700w, and what have you already test these montages? I need these montages, what are your conditions? Thank you, Yvon.DRC

    ReplyDelete
  3. I wish I could get sprint design full version or design spark full version even if it a cracking version. To rectify some class D pcb. [email protected]

    ReplyDelete
  4. Hello,
    can you tell me the value of 2 capacity under the PCB of Final Transistor ?
    Thanks

    ReplyDelete
  5. Hello,
    the impedance that must be done WITH THE 1.5 THREAD, must be wrapped around the 10ohm resistance? how many turns should be made?,

    ReplyDelete
  6. Hello , when you have hesitation test it with 24 +/- Vcc and when it is ok test with max power 60+/- Vcc ,
    I'm very impressed to the vibration to do this amplifier

    ReplyDelete
  7. Hi Mr Eko, Does can i get the printed pbc to this particular amplifier diagram? also where could be buy it and how much cost? Thank You...

    ReplyDelete
  8. You can download the PCB in the Download section, but for this PCB i havent ready to sell it.

    ReplyDelete
  9. Is it possible to send me better quality PCB, and layout files, also schematic diagram please [email protected]

    ReplyDelete
  10. Where I have to connect 2 100n 2 75v capacitor under the pcb of final transistors ? I mean which pins of the circuit? It's not clear in the video.

    ReplyDelete
  11. sir
    I don't find component list
    help me plz

    ReplyDelete
  12. This one is good,, but need to rebiased ,
    Sometime there is small distortion thats why..
    I made 4 pairs of 1943/5200 using 103 dc voltage rail and it is stable in 4 ohms load

    ReplyDelete
  13. Sir, i just want to ask how much power each each channel can produce if loaded with 8ohm,4ohm,and 2ohm.thanks

    ReplyDelete
  14. By the way I'm using 8 set of sanken 2sa1216 and 2sc2922 a total of 16transistors power output

    ReplyDelete
  15. And my power supply at 25ampere or even more at 90v symmetric

    ReplyDelete
    Replies
    1. its good power supply your amplifier is better than this

      Delete
  16. Cai i use this 2SC5200/2SA1943 ?

    ReplyDelete
  17. Sir How can you help in buying a high quality transistor can u help me with a link

    ReplyDelete
  18. ola amigo...tengo una fuente de 126-0-126 voltios DC sera q estas targetas me sirven

    ReplyDelete
  19. hola a migo como yo podria adquirir ese amplificador contodo y fuente si lo envia fuere del pais o si tienes en venta la fuente conmutada voltage cimetrico para 18 trancitores 2sc5200 y 2sa1943

    ReplyDelete
  20. where can i buy these components sir? or better the kit...

    ReplyDelete
  21. sir mujhe 1400watt yiroshi power amplifier ka pcb and Components knha milege




    ReplyDelete
  22. whatts the cost of this amplifier

    ReplyDelete
  23. this is where you can purchase amplifier
    https://www.ebay.com.au/itm/123348336072

    ReplyDelete
  24. can i use this amp driver circuit with +75 0 -75v dc ,in 1943 and 5200 transistor ?

    ReplyDelete
    Replies
    1. https://www.ebay.com.au/itm/123450646836

      Delete
  25. hi were can i get the parts for these amps or can i get them as a kit, can someone help thanks

    ReplyDelete
  26. https://www.ebay.com.au/itm/123574679995?var=&ssPageName=STRK:MESELX:IT&_trksid=p3984.m1555.l2649

    ReplyDelete
  27. where can i buy the complit kit, driver board, auput board with components and the power supply

    ReplyDelete
  28. please i need company like jlcpcb.com but accept to print the circuit by pdf or pcblayout

    ReplyDelete
  29. PCB s and parts here follow links for each one https://www.ebay.com.au/itm/123574710153?var=&ssPageName=STRK:MESELX:IT&_trksid=p3984.m1555.l2649
    https://www.ebay.com.au/itm/123561661498?var=&ssPageName=STRK:MESELX:IT&_trksid=p3984.m1555.l2649
    https://www.ebay.com.au/itm/123561788688?ssPageName=STRK:MESELX:IT&_trksid=p3984.m1555.l2649

    ReplyDelete
  30. Hi Mr Wahyu Eko Romadhon please chare the correct schematic for the PCB Stereo Yiroshi Amplifier,many difference between the video and Pcb ,thank you.

    ReplyDelete
  31. Can i use mjl4302/mjl4281for the final transistor?

    ReplyDelete
  32. Hi sir i just need to ask where to adjust dc offset of this amp i need to adjust to 0V dc there's only one trimpot but adjust only for the current bias.

    ReplyDelete
  33. Bhai apne PCB draw karne ke liye kinda paper liya tha

    ReplyDelete
  34. hi sir pls give me the components list

    ReplyDelete
  35. get amp kit here https://www.ebay.com.au/itm/123672424107?var=&ssPageName=STRK:MESELX:IT&_trksid=p3984.m1555.l2649

    ReplyDelete
  36. Hello. please give me the parts list, pcb's power supply source diagrams and all diagrams clear print out or soft copies. kindly provide me the complete estimate at [email protected] thankx

    ReplyDelete
  37. sir i made this diagram and it worked well but the negative driver
    transistor is heating teribly.how can i bias it perfectly?

    ReplyDelete
  38. Hello. It is 8ohms impedance? or below? Tank you sir.

    ReplyDelete
  39. Thanks for this job and great job ....
    I have some questions
    1. Can i use this amplifier for 2ohm load ?
    2. Can i use this for 4ohm load ?
    3. What is the maximum dc voltage rails cbe used to operate this amplifier at maximum output? ,,, +140-0-(-140) dc can be used ???

    ReplyDelete
    Replies
    1. actually cannot for 140VDC symmetrical

      Delete
  40. the two 220 resistors keep burning can anyone help?

    ReplyDelete
  41. Why I can't download the pcb layout,,what is the dimension of pcb for this nice Project.

    ReplyDelete
  42. si tiene problemas el esquematico y el pbc so miy diferentes

    ReplyDelete