Skip to content Skip to sidebar Skip to footer

Booster Amplifier circuit ( Transistor Final )

The circuit of booster amplifiers or amplifier end of a power amplifier circuit, Circuit over in the most important influence whether or not , and many more are affected in this final amplifier circuit.

Final amplifier , Booster Amplifier circuit ( Transistor Final )
Booster Amplifier Circuit Diagram :
Booster Amplifier Circuit Final Transistor


Because the booster circuit is the amplifier end of the work was too heavy components causing the rapid component of the heat. If you are wrong when install the components,  that can cause fatal damaged the component , such us the installation of pin emiter, collector , and base everything must be correct.

In the circuit above can strengthen booster amplifier with maximum work and everything is evenly split, what is it evenly split ? evenly split the point here is that all components can work with the same voltage and the heat evenly , this is because at each respetive base transistor were given the same constrains and same wattage resistor. And to maintain if the power output is too large then the resistor on Re will hamper so that the transistor is not easily broken.

Part List Booster Amplifier / Final Transistor :
Rb=10R/1W
Re=0,5-1R/5W
Q1=Transistor power NPN such us 2N3055 , TIP3055,TIP120,TIP142,2SC2922 , 2SC5200 , etc.
Q2=Transistor Power PNP such us MJ2955 ,TIP2955,TIP125,TIP147,2SA1216, 2SA1943 , etc.
X1=Voltage connector (-)
X2=PNP Base connector
X3=Speaker connecor but also must be connected from the buffer
X4=NPN base connector
X5=Voltage connector (+)
2SC5200 2SA1943
2SC5200 2SA1943 Ex Transistor Final

 PCB Layout Booster amplifier ( Transistor Final )

PCB Layout Booster amplifier ( Transistor Final )

For power amplifier driver you can search here: Power Amplifier Circuit

[VIDEO] See Also Assembling Final Transistor Amplifier 

21 comments for "Booster Amplifier circuit ( Transistor Final )"

  1. This comment has been removed by the author.

    ReplyDelete
  2. Thanks sir! Perfect layout schematic diagram very nice!

    ReplyDelete
    Replies
    1. Hello jhun,

      Thanks for your visit and hope you enjoy surfing in here. in elcircuit dot com.

      Delete
  3. how many volts DC minimum and maximum for this booster amplifier

    ReplyDelete
    Replies
    1. Hello henry,

      Its same as voltage power amplifier. For example you make 1600W the power supply voltage from 60 up to 100V dc, so the voltage of booster tramsistor is sam 60 upto 100V DC.

      Thanks Henry,
      HOPE YOU ENJOY in elcircuit.

      Delete
  4. THANK YOU VERY MUCH FOR THE INFORMATION,


    Thanks Mr.Wahyu

    ReplyDelete
    Replies
    1. Hello Henry,

      Youre welcome, dont be hesitate to ask with me, may i can help you.

      Thanks

      Delete
  5. Connect must by like this? (Or in place TIP36C-TIP35C?)
    https://drive.google.com/file/d/0B7s82YdStJGRQWk3bnZJZWxXVlU/view?usp=sharing

    ReplyDelete
  6. u must replace the tip35c tip36c, and connet x4 to emitter bd139 and x2 to emitter bd140

    ReplyDelete
  7. nice design,,, but where can i input and its output for speaker,, is it ok to have no driver/?

    ReplyDelete
  8. output ke bad ka cirki dalo thanku

    ReplyDelete
  9. i will make this if someone is gonna sale me a parts...nice schem

    ReplyDelete
  10. good morning, how many millivolts should the bias trimmer be calibrated? And the second trimmer? Sincerely Marcuzzi Rudi.

    ReplyDelete
  11. La resistenza R8 รจ da 3k3 oppure 33k ? Il progetto cosa richiede ?

    ReplyDelete